Surface charge density and induced currents by self-charging sliding drops.

Spontaneous charge separation in drops sliding over a hydrophobized insulator surface is a well-known phenomenon and lots of efforts have been made to utilize this effect for energy harvesting. For maximizing the efficiency of such devices, a comprehensive understanding of the dewetted surface charge would be required to quantitatively predict the electric current signals, in particular for drop sequences. Here, we use a method based on mirror charge detection to locally measure the surface charge density after drops move over a hydrophobic surface. For this purpose, we position a metal electrode beneath the hydrophobic substrate to measure the capacitive current induced by the moving drop. Furthermore, we investigate drop-induced charging on different dielectric surfaces together with the surface neutralization processes. The surface neutralizes over a characteristic time, which is influenced by the substrate and the surrounding environment. We present an analytical model that describes the slide electrification using measurable parameters such as the surface charge density and its neutralization time. Understanding the model parameters and refining them will enable a targeted optimization of the efficiency in solid-liquid charge separation.

High Voltages in Sliding Water Drops.

Water drops on insulating hydrophobic substrates can generate electric potentials of kilovolts upon sliding for a few centimeters. We show that the drop saturation voltage corresponds to an amplified value of the solid-liquid surface potential at the substrate. The amplification is given by the substrate geometry, the drop and substrate dielectric properties, and the Debye length within the liquid. Next to enabling an easy and low-cost way to measure surface- and zeta- potentials, the high drop voltages have implications for energy harvesting, droplet microfluidics, and electrostatic discharge protection.

Charging of Dielectric Surfaces in Contact with Aqueous Electrolytes─the Influence of CO2.

The charge state of dielectric surfaces in aqueous environments is of fundamental and technological importance. Here, we study the influence of dissolved molecular CO2 on the charging of three chemically different surfaces (SiO2, Polystyrene, Perfluorooctadecyltrichlorosilane). We determine their charge state from electrokinetic experiments. We compare an ideal, CO2-free reference system to a system equilibrated against ambient CO2 conditions. In the reference system, the salt-dependent decrease of the magnitudes of ζ-potentials follows the expectations for a constant charge scenario. In the presence of CO2, the starting potential is lower by some 50%. The following salt-dependent decrease is weakened for SiO2 and inverted for the organic surfaces. We show that screening and pH-driven charge regulation alone cannot explain the observed effects. As an additional cause, we tentatively suggest dielectric regulation of surface charges due to a diffusively adsorbed thin layer of molecular CO2. The formation of such a dynamic layer, even at the hydrophilic and partially ionized silica surfaces, is supported by a minimal theoretical model and results from molecular simulations.

Spontaneous Charging of Drops on Lubricant-Infused Surfaces.

When a drop of a polar liquid slides over a hydrophobic surface, it acquires a charge. As a result, the surface charges oppositely. For applications such as the generation of electric energy, lubricant-infused surfaces (LIS) may be important because they show a low friction for drops. However, slide electrification on LIS has not been studied yet. Here, slide electrification on lubricant-infused surfaces was studied by measuring the charge generated by series of water drops sliding down inclined surfaces. As LIS, we used PDMS-coated glass with micrometer-thick silicone oil films on top. For PDMS-coated glass without lubricant, the charge for the first drop is highest. Then it decreases and saturates at a steady state charge per drop. With lubricant, the drop charge starts from 0, then it increases and reaches a maximum charge per drop. Afterward, it decreases again before reaching its steady-state value. This dependency is not a unique phenomenon for lubricant-infused PDMS; it also occurs on lubricant-infused micropillar surfaces. We attribute this dependency of charge on drop numbers to a change in surface conductivity and depletion of lubricant. These findings are helpful for understanding the charge process and optimizing solid-liquid nanogenerator devices in applications.

Tuning the Charge of Sliding Water Drops.

When a water drop slides over a hydrophobic surface, it usually acquires a positive charge and deposits the negative countercharge on the surface. Although the electrification of solid surfaces induced after contact with a liquid is intensively studied, the actual mechanisms of charge separation, so-termed slide electrification, are still unclear. Here, slide electrification is studied by measuring the charge of a series of water drops sliding down inclined glass plates. The glass was coated with hydrophobic (hydrocarbon/fluorocarbon) and amine-terminated silanes. On hydrophobic surfaces, drops charge positively while the surfaces charge negatively. Hydrophobic surfaces coated with a mono-amine (3-aminopropyltriethyoxysilane) lead to negatively charged drops and positively charged surfaces. When coated with a multiamine (N-(3-trimethoxysilylpropyl)diethylenetriamine), a gradual transition from positively to negatively charged drops is observed. We attribute this tunable drop charging to surface-directed ion transfer. Some of the protons accepted by the amine-functionalized surfaces (-NH2 with H+ acceptor) remain on the surface even after drop departure. These findings demonstrate the facile tunability of surface-controlled slide electrification.

Charging of drops impacting onto superhydrophobic surfaces.

When neutral water drops impact and rebound from superhydrophobic surfaces, they acquire a positive electrical charge. To measure the charge, we analyzed the trajectory of rebounding drops in an external electric field by high-speed video imaging. Although this charging phenomenon has been observed in the past, little is known about the controlling parameters for the amount of drop charging. Here we investigate the relative importance of five of these potential variables: impact speed, drop contact area, contact line retraction speed, drop size, and type of surface. We additionally apply our previously reported model for sliding drop electrification to the case of impacting drops, suggesting that the two cases contain the same charge separation mechanism at the contact line. Both our experimental results and our theoretical model indicate that maximum contact area is the dominant control parameter for charge separation.